What're your beliefs about A Step-by-Step Guide to Installing a Bathtub?
Mounting a bath tub isn't specifically brain surgery, however it does need solid plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably tough job. If the old tub is readily easily accessible, the job can move rapidly; if you need to open up a wall surface to eliminate the old tub and position the new bathtub, the task is much harder. In either case, the project is within a home handyman's skills, although you will certainly require an assistant to move out the old tub and embeded in the brand-new one. See to it you have actually certified on your own for the task as well as are comfortable attempting it. Rather than hiring a specialist to take over a halfway-completed job, it is better to consider employing one prior to you start. Opportunities are you might need a professional plumber to make tube links.
This write-up will certainly assist you set up a new bathtub in your bathroom if you have actually currently gotten a new tub and also do not require to change the setup of your previous water system pipes.
Your tools and also product checklist should consist of the following:
Planning for the Setup
First of all, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to see to it that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to stop stress on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must now be ready to be suited its final placement.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the supply of water. After doing so, activate the taps to drain any kind of water remaining in the system. The process of getting rid of the existing taps can be rather bothersome due to the restricted access that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly come from the pipes. When the supply pipelines have actually been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning during this process. When the taps have been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Before proceeding to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Installing the Bathtub
Using the two wooden boards under its feet, place the bath tub in the called for placement. The wood boards are handy in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also adjusting the feet on the bathtub till the level checks out level.
To install taps, fit all-time low of the outermost versatile tap connector to the ideal supply pipeline by making a compression join; then do the same for the various other faucet.
Turn on the supply of water and examine all joints as well as new pipework for leaks and also tighten them if needed. Fill up the bath tub as well as also check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, take care of the bath paneling as explained in the producer's user's manual. Tiling and also sealing around the bathtub must wait until the bath tub has been utilized at the very least when as this will resolve it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washers remain in place between the faucet and the sink. Protect the tap in position with the manufacturer supplied backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous type must be attached to the tap finishes initially, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to fracture a rigid seal, triggering the water to pass through the wall in between the bath and also the tiling, leading to problems with wetness and possible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures and installations. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched paper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to enable the activity experienced when the tub is in use. The sealant can split rather very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the tiles using water-resistant or waterproof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very enthusiastic about How to Install a Bathtub and I'm hoping you appreciated the post. So long as you enjoyed reading our post please make sure you remember to pass it around. Thanks for your time. Visit us again soon.
Check This Out
Bug Hall Then & Now!
Amanda Bearse Then & Now!
David Faustino Then & Now!
Marcus Jordan Then & Now!
McKayla Maroney Then & Now!